<h2>What is a Class 3 Dealer?</h2><p>
	A person or business that has a Type 01 Federal Firearms License that has a class 3 tax stamp that allows them to posses and transfer Title II NFA firearms.</p><h2>What are NFA firearms?</h2><p>
	The National Firearms Act enacted on June 26, 1934 in general, imposes a statutory excise tax on the manufacture and transfer of certain firearms and mandates the registration of those firearms. The Act was passed shortly after the repeal of Prohibition. The NFA is also referred to as Title II of the Federal firearms laws. The Tax amount is usually $200 depending on the type firearm. The Most common NFA Items are: Silencers, Short Barrel Rifles (SBR) and Machine Guns.</p><h2>How can I transfer or purchase a NFA item?</h2><h3>1. Register the NFA item to a trust</h3><p>Advantages of registering to a trust:</p><ol>
	<li>No signature is required from chief law-enforcement officer</li>	<li>You only need to create the trust once. The same trust can be used for all future NFA items such as short barreled rifles machine-guns or any other weapons.</li>	<li>Fingerprint cards are required</li>	<li>Anyone listed as a trustee in the trust can be in possession of the suppressor</li>	<li>A revocable trust can be changed at any time without notifying the ATF</li></ol><h3>2. Register the NFA item to a corporation</h3><p>
	Advantages of registering to a corporation:</p><ol>
	<li>No signature is required from chief law-enforcement officer</li>	<li>Fingerprint cards are required</li>	<li>Any officer of the corporation can be in possession of the suppressor</li>	<li>If you already have a corporation, this can be easier than a trust since you will avoid the initial trust setup</li></ol><h3>3. Register the NFA item in your own name</h3><p>
	You can avoid initial work required to setup a trust or corporation. You have to remember that only you can be in possession of the NFA Item. This Requires signature from chief law-enforcement officer where you live and fingerprint cards.</p><p>
	Here at DEGuns we want to simplify the process as much as possible and we will explain how the transfer process works. NFA transfers can take anywhere from 2-9 month and you have to remember the process starts when your paperwork is sent the the NFA Branch for approval. It is very important to have everything needed. We do not give legal advice or sell trusts.</p><h2>Registration and Requirements</h2><p>The process of acquiring a Class 3 firearm, or a National Firearms Act (NFA) device, can be straightforward and relatively easy once you understand the necessary steps. Here's a more detailed guide to facilitate the process:</p><ol><li>Select your firearm: Start by choosing the Class 3 weapon that you're interested in purchasing. This could be anything from a machine gun, suppressor, or short-barrelled rifle, to other types of NFA regulated devices. Keep in mind that different states have varied regulations regarding these devices, and it's crucial to ensure that your desired firearm complies with your state's laws.</li><li>Complete the Form 4 with your dealer: Form 4, or the Application for Tax Paid Transfer and Registration of Firearm, is a necessary document when purchasing a Class 3 weapon. This form should be filled out with the help of your firearms dealer, who will assist in providing pertinent information regarding the device you're buying.</li><li>Acquire necessary photos and fingerprints: You must have a set of passport-sized photos and fingerprint cards to include with your application. These are used for identification purposes and are part of the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) background check process.</li><li>Submission of documents: After gathering all necessary documentation, including your completed Form 4, photographs, and fingerprints, send it to the ATF for processing.</li><li>Waiting period: The approval process for purchasing a Class 3 weapon typically takes several months. During this time, the ATF performs extensive background checks.</li><li>Collection of the device: Once the ATF approves your application, you can then pick up your Class 3 firearm from the dealer. The timing of this can vary based on several factors, including the type of firearm and your location.</li></ol><p>In essence, the process is straightforward, although it may involve some additional paperwork depending on the specific firearm you're purchasing and the laws of your state.</p><p>Several misconceptions often surround the ownership of NFA devices, and it's crucial to address these to ensure you're well-informed:</p><ul><li>House Searches: ATF or other law enforcement agencies cannot randomly search your home for your NFA device. However, they can request to see the device if there's a valid reason for doing so.</li><li>Tax Stamp Documentation: Although you receive an original tax stamp (proof of payment of the excise tax for your firearm) when your Form 4 is approved, you're not required to carry it with you at all times. A copy will suffice for most situations, but ensure the original is kept safe.</li><li>Change of Location: Should you relocate, it's essential to notify the ATF of the new location of your NFA device.</li><li>Reselling NFA Devices: You can't sell your NFA device without the buyer completing a Form 4 transfer. The buyer must undergo the same process you did, including the payment of the tax and approval by the ATF.</li><li>Nature of the Tax Stamp: The tax stamp is not a license but rather an indication that you've paid the required tax on your NFA device.</li></ul><p>Acquiring an NFA device like a suppressor or a short-barrelled rifle doesn't pose any significant burden, provided you follow the rules and regulations stipulated by the ATF and safely store your tax stamp.</p>

What is a Class 3 Dealer?
	A person or business that has a Type 01 Federal Firearms License that has a class 3 tax stamp that allows them to posses and transfer Title II NFA firearms.What are NFA firearms?
	The National Firearms Act enacted on June 26, 1934 in general, imposes a statutory excise tax on the [...]

How to Buy a Class 3 NFA Item From a Class 3 Dealer

<h2>How to Zero Your Optic or Scope</h2><p>
	Whether you’re sport shooter, hunter, prepared citizen, or all three, your rifle is as useless as an ejection seat in a helicopter if you haven’t learned how to zero your scope or optic. In this post, we’ll teach you how to zero your scope or <a href="https://www.deguns.net/optics-scopes-and-sights">optics</a> in 3 easy steps, as well as all the materials needed to do so.</p><h3>What you’ll need:</h3><ul>
	
<li>Paper targets with a standard .5” grid pattern printed on them, preferably large ones</li>	
<li>Your optic’s user manual</li>	
<li>A flathead screw driver (depending on your particular optic’s windage/elevation control)</li>	
<li>An allen wrench (whatever size is needed to tighten/loosen the screws that fasten your optic to your weapon’s rail)</li>	
<li><a href="https://www.deguns.net/ammo">Ammo</a> (preferably the same ammunition you plan on firing after you’re zeroed)</li>	
<li>A<a href="https://www.deguns.net/boresight?_q=boresight&map=ft"> boresight</a></li>	
<li>A <a href="https://www.deguns.net/spotting%20scope?_q=spotting%20scope&map=ft">spotting scope</a></li></ul><h3>Step 1: Preparation</h3><p>
	Now that you have the above materials and tools gathered, let’s go through a preliminary check:</p><p>
	Distance: Decide the distance at which you plan to zero your optics. This should be a distance from which you are both comfortable shooting and reasonable for your particular rifle’s effective range. At minimum, 25 yards is recommended for optics with minimal or no zoom function, such as standard reflex sights, red dot sights, and tactical scopes. <a href="https://www.deguns.net/optics-scopes-and-sights/rifle-scope?initialMap=c&initialQuery=optics-scopes-and-sights&map=category-1,optics">Rifle scopes</a> with higher magnification should be sighted at 50 or more yards. You want to decide what distance you will most likely be using it. Don’t worry, if you are wondering “what if my shot is outside of that zero range?”. It is completely possible to shoot outside of this designated zero if necessary by just lowering or raising the crosshair according to your ammunitions trajectory.</p><p>
	Each caliber will yield different trajectory characteristics that are necessary to know in assessing how much to raise or lower the reticule when firing at targets outside of your zero range, be they closer or further than that zero distance. For example, if you are zeroed at 50 yards and your bullet is still on its way up at 100 yards, you may need to lower your reticule a certain amount when aiming for targets at 100 yards. If it’s on its way down at 200 yards, then you may need to raise your reticule when firing at targets that are 200 yards away. Again, it all depends on what your particular bullets are doing at a given range.</p><p>
	Secured Optic: Make darn sure that your scope or reflex sight is securely fastened to your firearm’s rail. This is where the allen wrench comes into play. If your optics aren’t secure, the recoil from your shots can move the position of the optic itself and/or the reticule ever so slightly, negating any fine tuning you have done up to that point. Understand that even the slightest change in reticule or optic position will yield a depreciating effect on accuracy that only intensifies at longer distances.</p><h3>Step 2: Hitting the Paper Target</h3><p>
	Whether your optic of choice is a rifle scope or <a href="https://www.deguns.net/firefield-impact-xlt-reflex-sight/p">reflex sight</a>, you need to obtain hits – any hits – on paper as a point of reference before you can begin fine tuning your zero. Simply put, you need visual confirmation of where your shots are hitting so that you can contrast these hits against what you see when you aim the reticule at the desired area of the target. Even simpler put, you can’t correct a problem until you identify what’s causing it.</p><p>
	When learning how to zero your optic or scope, you now need to take your first three shots at the paper. Be sure to aim your reticule as close as you can on the same spot every time. To clarify, shooting in groups ensures that shooter error has minimal effect on the zeroing process and that we can consistently hit a given target where we want to.</p><p>
	The practical test is that when three shots are fired while aiming at the same area of the target, they land relatively close together. Keep in mind that at this stage, it doesn’t matter so much whether or not these shots land where your reticule is aimed, but rather that they are hitting the same area of the target. For example, if your reticule is aimed at the bottom right of the target, and all three shots are grouped together at the bottom left, we can be sure in our consistency and be confident that shooter error won’t cause a problem when calculating the next adjustment.</p><p>
	Suffice it to say, if you hit the paper at all and you have tight groups, it’s time to move to the next step in the zeroing process.</p><p>
	If you AREN’T on the paper, then it’s time to employ a boresighter to get on it. Understand that boresighters don’t zero optics, but rather offer a starting point to get on paper so that the shooter may then zero in. Using a boresighter is simple. Attach it to your rifle, turn it on, and then line up your optic’s reticule to the point generated by the boresighter. From there, you should be able to get on the paper.</p><h3>Step 3: Fine Tuning Your Optics to Zero</h3><p>
	Assuming that you are firing from a consistent range and are hitting the paper, it’s time to fine tune your sights. All optics, regardless of make or model, come equipped with elevation and windage knobs, allowing precise control of the reticule’s x and y axis. The elevation knob is responsible for adjusting the vertical position of the reticule, and the windage knob is responsible for adjusting the horizontal position of the reticule.</p><p>
	These knobs are “stepped”, meaning that with each click sound heard and/or felt as a knob is turned, predictable bullet movement is ensured. Previously, we suggested that you use targets with a .5” grid pattern. This comes into play with the stepped knobs because with each step on a knob, a precise amount of bullet movement can be expected at a given range.</p><p>
	This is the point at which you should consult your optic’s user manual to determine how many clicks it takes to move your shots a given amount at a given distance. Once you know how many clicks equal 1 or ½ inches of bullet movement for your particular optics at a given range, you can easily calculate how many clicks it will take to move your shots “2 inches to the left and 6 inches up”- or whatever is needed – using the .5” grid background as your reference for calculation. Depending on your distance to target and your eyesight, a spotting scope may be needed to see the grid pattern well enough to make your calculations. At 50 yards or more, you will most definitely need one to make these judgments accurately.</p><p>
	For example, if a single click yields .5” of bullet movement at a range of 50 yards, then moving shot placement 2” down and 4” to the right will take 4 clicks down and 8 clicks to the right.</p><p>
	Don’t forget to fire your shots in groups of 3 each time in order to ensure consistency and accuracy in your adjustments.</p>

Whether you're sport shooter, hunter, prepared citizen, or all three, your rifle is as useless as an ejection seat in a helicopter if you haven't learned how to zero your scope or optic. In this post, we’ll teach you how to zero your scope in 3 easy steps.

How to Zero Your Optic or Scope
	Whether you’re sport shooter, hunter, prepared citizen, or all three, your rifle is as useless as an ejection seat in a helicopter if you haven’t learned how to zero your scope or optic. In this post, we’ll teach you how to zero your scope or optics in 3 easy [...]

Zeroing a Scope in 3 Easy Steps

DEGuns

MASP Industries

Heckler & Koch

Magpul

Alexander Arms

Volquartsen Firearms

Surefire

Geissele Automatics

Spike's Tactical

Mission First Tactical

Timney Triggers

Blade Tech

Mil Comm

KNS Precision

Nighthawk Custom

Dan Wesson Firearms

Apex Tactical Specialties

Wilson Combat

ATN Corp

Glock

SIG SAUER

Daniel Defense

Nemo Arms

Aero Precision

Arsenal Firearms

Aimpoint

Vortex Optics

EOTECH

Smith & Wesson

CZ-USA

HANDI-RACKER

STEINER

EDGE TACTICAL SAFETY EYEWEAR

DRAGO GEAR GUN CASES AND BAGS

LASERLYTE

Bravo Company Manufacturing (BCM)

DEL-TON

DPMS PANTHER ARMS

BENELLI

Stoeger

Uberti

FRANCHI

IO INC

SilencerCo

Springfield Armory

POF USA PATRIOT ORDNACE FACTORY

TAC-CON 3MR AR-15 AR-10 RAPTOR AK-47 TRIGGERS

Ruger

GHOST INC PARTS

SCCY INDUSTRIES FIREARMS

LASERMAX WEAPON LASERS AND LIGHTS

EAA Corp

FOXPRO High Preformance Game Calls

THUNDER BEAST SILENCERS

Kimber America

Kel-Tec Weapons

CAA Industries

Christensen Arms

TACTICAL SOLUTIONS

NCStar Products

Salient Arms International

Montana Rifle Company

RUDOLPH OPTICS

MANTA Products

UNDER ARMOUR

Thompson Center Arms

LEUPOLD

Hornady

Savage Arms

Streamlight

RAMBO BIKES

Walther Arms

Sako

Remington Arms

HOMAK

BERETTA

Pelican Brand Cases and Coolers

Crossbreed Holsters

Browning Arms

Boker Knives

Schmidt & Bender

DT Systems Dog Training Equipment

Altus Brands

Warne Scope Mounts

SnapSafe

MTM Case-Gard Storage Containers

SCHRADE KNIVES

BUCK KNIVES

Walker's Game Ear

Hearing Protection

Winchester

PANTHER VISION

CENTURY INTERNATIONAL ARMS

NOMAD

Carlson's Choke Tubes

Arctic Shield

CASIO

Double Tap Blog

Contact

sportsouth

<h2>Product Features & Specifications</h2>Troy Ind SSIGFBSFHFT BattleSight Front Folding HK AR-15/M4/M16 Aluminum FDE

Troy Ind BattleSight Front Folding HK AR-15/M4/M16 Aluminum FDE